How can I connect multiple speakers to one channel on an amp?

Sync your iOS device including music over a shared Wi-Fi connection You can use a third-party audio device to connect speakers to your Mac. Install drivers for the audio device, if needed, before you plug the device into the Mac. You need to install a driver if: Then use GarageBand to record the music on your Mac. To record from your home stereo to your Mac, follow these steps: Attach the RCA connectors to your stereo receiver’s auxiliary aux output. This might be called “Record” or “Tape Out” on some receivers. Connect the other end of the cable to the audio input port on your Mac or to your Mac-connected audio interface. Turn on your home stereo.

Theater Solutions

The most basic way to wire marine speakers to an amplifier is to connect one speaker to each of the available channels. But there are other options to consider. Most external amplifiers can power more than one speaker per channel. For example, a 4 channel amplifier may be able to power up to 8 speakers.

This does not cause a power draw on the amp you hook up to. It is merely sharing the signal with your main speakers, not the power of the amp. This means there is no power draw, and the impedances all remain the same.

Just what is tone? What is a good tone and how do you achieve it? Which amps you should choose for your setup and how to get the tones you want. We also looked at the importance of choosing the right guitar — not only for your technique and rig but also for inspiration to play and create music. Check out part 1 and part 2. Amps People tend to prioritize guitars and a bunch of pedals and forget the importance of a good sounding amp. Choosing the right amp for your setup is crucial for getting the tones you want from your guitar and pedals.

Speaker hook up

How to find your Total Score? Add up the points from each column of the above table to find your Total Score. A Detailed Look at your Conditions Determining questions on adding an amp: So what are your listening habits like? Do you often listen at ear-bleeding levels that would send your mother-in-law out of your room in a hysterical rage, or do you listen at levels where you can still have a comfortable conversation?

How big is your room?

Oct 07,  · A speaker selector is a device that splits the audio signal coming from your receiver or amplifier and sends that same audio signal to two or more sets of speakers. A speaker selector is usually a passive device that uses the amplification power from your receiver or power amplifier to power connected speaker pairs.

This confusion is also a likely cause of many blown power amplifiers. This article is intended to explain the meaning of speaker impedance and guide the reader in connecting multiple speakers to an amplifier. This article is NOT intended for engineers, technicians, or even serious students of electronics technology. What are ohms, anyway? The ohm is the unit of measure for impedance, which is the property of a speaker that restricts the flow of electrical current through it.

Typical speakers have impedance ratings of 4 ohms, 8 ohms or 16 ohms. For the average audio user, the nominal impedance is the dominant characteristic and for the purposes of this discussion, we will use the nominal value of the speaker’s impedance. Why are ohms important? Too many speakers on a solid state amp can burn up the power output section. Too low an impedance will result in weak output and poor tone. If the speaker impedance is higher than that of the amplifier, its power output will again be less than it is capable of.

How to Use A Speaker Selector for Multi-Room Audio

Impedance is one of the most important terms to understand when configuring your needs for a whole house audio system; and will ultimately lead to better system performance and less installation frustration. Trying to understand impedance can be an intimidating process, but it was explained to me using a very simple analogy and I will do the same for you.

Most home speakers are 8 Ohm, but do not work under this assumption, ask the dealer or look on the box [All of Theater-Solutions are 8 Ohm]. Think of your water pipes and pump at home.

You don’t state what amplifier you are considering in this system. Many people refer to a receiver as an “amplifier”. I’ll assume you mean a separate power amplifier since you understand what a pre amp does.

Equalizers What are power amplifiers? Power amplifiers are devices that amplify electrical signals that have been adjusted to an appropriate volume and tone sent from the mixer, to a level that can be converted to acoustic sounds by the speakers. There are various types and models of power amplifier, varying in size, shape and output power, which are suited to different situations. There are three major types of power amplifier, the characteristics of which are described below.

Stand-alone power amplifiers amplify the signals sent from mixers to make the speakers produce sound. Several stand-alone power amplifiers can be installed together in racks, making it comparatively easy to build a large-scale PA system. Since the mixer and power amplifier which require a power supply are integrated into the PA system, only one power supply connection is required, and there are less connections to make than with stand-alone amplifiers. Since the built-in power amplifier is designed specifically for the speaker, the speaker and power amplifier combination feature superior compatibility, allowing the speaker to perform to the fullest.

The mixer output can connect directly to the powered speaker, so there are less cables required. To build a PA system as easily and simply as possible, use either a powered mixer or powered speakers, which require fewer connections. However, stand-alone amplifiers offer a higher level of freedom, for expanding a system and for planning where to position the equipment.

Choosing power amplifiers In this section, advice is given about choosing a power amplifier used in combination with passive speakers.

Multiple speakers in same outlet

Prince Clash 1 year ago Reply Prince Clash 1 year ago Reply please can u tell me how to connect those magnet wires into mobile jack JustinL3 2 years ago Is it ok if you use conducting wires? YunusK 2 years ago Reply Do you mean wire with no insulation? Unfortunately no, the current must be forced to go around the coil, but if it is not insulated, the current would just flow straight through the big chunk of the coil to the other end without creating the electromagnetic force.

Did this for the second time with my physics students, they love it! Thin, insulated magnet wire is the best. The thinner wire makes the resistance more like 8 Ohms, the resistance of a normal speaker.

May 05,  · Speaker hook up. By boeingfixer · 16 replies Get an amplifier, connect the speakers to the amp. Get a Y cable to connect the sound card line out/speaker out to .

The speaker cabiners had the sockets labelled IN and OUT, which means they had been designed for this sort of connection. I wonder whether the same setup – multiple speakers hooked on single amp output – is possible with standard consumer home audio systems as my Cantons dont’t have the OUT connectors. I’m only interested in the technical aspects, not in how the fidelity may degrade I only use coat hangers to connect my speakers.

I’m not very well educated in this field, so I’d like to provide some of reasoning I’d already done, in case there is something to correct in there, too. I understand that one should never connect a speaker box of impedance lower than that for which the amplifier is designed so you can connect 8 Ohm speaker to 4 Ohm rated amp but not the other way around. I’d count that impedance behaves quite like resistance in that, that if I connect the speakers in parallel, I’d end up with half total impedance and would need a 4 Ohm rated amp for a pair of 8 Ohm rated speakers.

With three of them, I’d be down to 2,5 Ohm rated amp for 8 Ohm speaker boxes. With speakers connected in series, I’d need an amp power rated roughly equal to the speaker power ratings combined but won’t need to worry about the impedance as long as the speakers are same or higher impedance than amp rating.

Connect your Mac to a iPod, iPad, home stereo, speakers, or musical instruments

Apex, NC therockman said: Use the tape aux. Of course there are other ways to acomplish the same thing, but this seems like the easiest. I second this idea with a couple of cautions. What you are hearing from the Pioneer could be the result of the pre-amp section, the amp section, or the synergy of both.

PA and Instrument Amp Speaker Cables; PC/Mac. Computer Adapters. Miscellaneous Computer Adapters; How to connect your Computer to your Stereo; How to connect your Computer to your Stereo. How to Connect your Computer (PC/Mac) to your Home Stereo: Many audio systems have tape ins and outs so you can connect up your computer through these.

Always a pleasure when people appreciate the time! Quote – ” To clarify, when an amp says 2ohm stable stereo, it really is saying that each channel can handle 2ohms for a 4ohm load rather than each channel can handle 1ohm for a 2ohm load right? On the face of it, 2 Ohms stable means guaranteed to work down into 2 Ohms without causing damage to the Amp, or limiting it’s full power into 2 Ohms. It ” should ” also mean that it’s capable of tolerating the expected impedance dips that can take it lower than 2 Ohms.

Whether a particular Amp does or not, should be obtained from the manufacturer in writing. Or maybe from a Reputable test in some mag or online etc. As i mentioned before, unless you are trying to run the Amp at anywhere near full power, you ” should ” be ok. Quote – ” Is it safe to only give watts rms to a speaker that is rated for watts rms? Is there a such thing as under powering?

How To Wire Speakers and Subwoofers to Your Amplifier – 2, 3, 4 and 5 Channel – Bridged Mode